mesh

“Under the hood” of SOLIDWORKS Flow Simulation

EmailFacebookLinkedInTwitterShare

The field of Computation Fluid Dynamics (CFD) is a sophisticated engineering discipline based on the Reynolds Averaged Navier-Stokes (RANS) equations that govern fluid flow, heat and mass transfer. CFD has a reputation for being extremely complicated and has typically been the domain of specialists, physicists and academics, using super computers. Typically, the quality of CFD results is greatly affected by the quality of the mesh and the attentiveness of the user to the pre-processing stage. Consequently, traditional CFD software codes […]

Read More

SOLIDWORKS 2020 What’s New – Mesh Support for More Features

EmailFacebookLinkedInTwitterShare

With the previous releases of SOLIDWORKS, we’ve seen some great enhancements for handling Graphics Mesh and Mesh BREP Bodies. With the release of SOLIDWORKS 2020, we see even more functionality for Mesh Bodies which now include support for the following commands: Shell Fillet Draft Chamfer Delete Face Fill Face Mutual Trim Surface Knit Delete Hole Additionally, if you’ve used any Mesh Body commands in previous versions, you will find that they have a new location in the UI. All Mesh […]

Read More

SOLIDWORKS: Flow Simulation Mesh Visualization Changes Implemented in SW2016

EmailFacebookLinkedInTwitterShare

Flow Simulation Mesh Visualization Changes   In SOLIDWORKS Flow Simulation, accurately and efficiently designing the mesh to capture the solid/fluid interface is critical to producing quality results. Doing so can be a challenge, so it’s important to see the mesh at the boundary to support further refinement, as needed.   Flow Simulation 2015 and previous releases allowed visualizing the mesh using “Mesh 3D View”, a tool that was a bit cumbersome to use and didn’t produce a clear view of […]

Read More

SOLIDWORKS: Meshing Errors in SOLIDWORKS Plastics 2016

EmailFacebookLinkedInTwitterShare

Meshing Errors in SOLIDWORKS Plastics 2016   When trying to mesh a runner system with the part in SOLIDWORKS 2016, you may end up getting errors that don’t give you a clue to what is wrong. For instance, take a look at this message: when sewing connector, it without any face error!! This message came up when I was creating a solid mesh. Not sure if the message is a direct translation from another language but it doesn’t give you […]

Read More

SOLIDWORKS TECH TIP: Meshing Tips and Tools for Better Results (Part 8 – Final)

EmailFacebookLinkedInTwitterShare

Since I am always being asked what makes a good mesh, I decided once again to blog about a list I put together a while ago. This was a general list, in no particular order, of things you can do, things you can use, and things you can look for in creating a mesh; knowing you have a good mesh, you can feel better about the results you are getting. This is the final part in this series. Here, I […]

Read More

SOLIDWORKS TECH TIP: Meshing Tips and Tools for Better Results (Part 6)

EmailFacebookLinkedInTwitterShare

Since I am always being asked what makes a good mesh, I decided once again to blog about a list I put together a while ago. This was a general list, in no particular order, of things you can do, things you can use, and things you can look for in creating a mesh; knowing you have a good mesh, you can feel better about the results you are getting. This is part 6 in the series and will look […]

Read More

SOLIDWORKS TECH TIP: Meshing Tips and Tools for Better Results (Part 3)

EmailFacebookLinkedInTwitterShare

Part 1 – Part 2 – Part 3 Since I am always being asked what makes a good mesh, I decided once again to blog about a list I put together a while ago. This was a general list, in no particular order, of things you can do, things you can use, and things you can look for in creating a mesh; knowing you have a good mesh, you can feel better about the results you are getting.This is part […]

Read More

SOLIDWORKS TECH TIP: Meshing Tips and Tools for Better Results (Part 2)

EmailFacebookLinkedInTwitterShare

Part 1 – Part 2 – Part 3 Since I am always being asked what makes a good mesh, I decided once again to blog about a list I put together a while ago. This was a general list, in no particular order, of things you can do, things you can use, and things you can look for in creating a mesh. And knowing you have a good mesh, you can feel better about the results you are getting. This […]

Read More

SOLIDWORKS TECH TIP: Meshing Tips and Tools for Better Results (Part 1)

EmailFacebookLinkedInTwitterShare

Part 2 – Part 2 – Part 3 Since I am always being asked “what makes a good mesh?” I decided once again to blog about a list I put together a while ago. This was a general list, in no particular order, of things you can do, things you can use, and things you can look for, in creating a mesh.  And knowing you have a good mesh, you can feel better about the results you are getting. This […]

Read More